English
Mon compte Créer un compte
English
EVO-START Wirecolor

Votre panier

Votre panier est vide.

Votre panier est vide.

Continuer le magasinage

TOTAL ESTIMÉ :

Commander

RECHERCHE RAPIDE DE VÉHICULE

RECHERCHE VÉHICULE

Utilisateur

Angel Enriquez

À rejoins en date due:

Jun. 25, 2017

Points

440

Commentaire(s)

7

Questions votée(s)

0

Réponses votée(s)

2

Votes positifs

0

Votes contre

2

Votes reçus

0

Votes négatifs reçus

0

Activité récente

Questions demandée(s)

5

Question(s) répondue(s)

1

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question
ACTIVITÉ RÉCENTE QUESTION(S) DEMANDÉE(S)" QUESTION(S) RÉPONDU(S)" QUESTION(S) COMMENTÉE(S)"

26/10/2021

 Dodge Angel Enriquez (440Pts.)

0

Automatically goes into valet mode while driving

Recently i have noticed that while driving randomly at no precise intervals and regardless of moving or stationary alarm chirps. I found this was the alarm going into valet mode. And regardless if it is already in valet mode it will do it again sometimes minutes later and sometimes 20 minutes later. So far it has never happened right after starting up. The alarm i have is a compustar with the Evo All. Any info or advice is appreciated. Thank you for your time.
Connectez-vous pour répondre Voir 1 réponse(s)

02/03/2020

 Dodge Angel Enriquez (440Pts.)

0

2013 Dodge Journey automatically unlock when pressing lock button

reinstalled after finding a loose wire and system was working off and on. After reinstalling the alarm, compustar CM600-AS, it is workingfor the most part however now when i press the lock button on the Compustar remote it locks and a second or 2 later it unlocks but alarm is still set. when i press unlock i can hear it pulse twice to unlock. previously i had done the standalone installing and for the most part had no issue with the exception of the loose wire but this time went with the standard installation. confirmed all the wires are connected correctly and date protocal is correct. i am sure it is a setting just not sure which one i will need to turn on or off. any help will be greatly apprciate it.
Connectez-vous pour répondre Voir 1 réponse(s)

21/04/2018

 Dodge Angel Enriquez (440Pts.)

0

Remote start not working

I was able to program the evo and connect it to my Compustar alarm. It now locks and unlocks through alarm. But when i try to use remote start it turns on ignition to run position but does not start. If i open door it turns off the ignition like it is suppose to. Guessing that is a setting in the programming but not sure which one.

this is for a 2013 dodge journey sxt push button and using a compustar CS6900-AS

Connectez-vous pour répondre Voir 1 réponse(s)

15/04/2018

 Dodge Angel Enriquez (440Pts.)

0

Programmig not working stuck at step 9

i have double and triple checked my wire connections but when i try to program my THAR-CHR6 and when i get to step 9 the light will not change from Red to blue. I have attempted this multiple times and have followed all the steps so i am lost and really could use some help. Could it be an issue with my unit or is there a trick to this i am missing. I am installing on a 2013 Dodge Journey Push button ignition. *Update* I had intially started i had updated my Evo to the most recent firmware not in beta. I downgraded to 74.22 and was able to get to the next step where the blue light would come on but it would not flash. Flashed it again to a higher FW believe 74.25 but same thing blue light doesn't flash. Otherthing i noticed is on the ODBII port guide says the CAN high wire is brown but there are no brown wires on that harness. The CAN low matches the yellow though.
Connectez-vous pour répondre Voir 1 réponse(s)

11/04/2018

 Other Angel Enriquez (440Pts.)

0

Vehicle unlocked not showing

I used my activation code and was able to see vehicle i entered and now that i return ti site says i have to either subscribe or use activation code to see same vehicle. Is there any way to correct this? It doesn't say anywhere there is a time limit for the activation code that camr with my fortin bypass.
Connectez-vous pour répondre Voir 1 réponse(s)

06/01/2018

 Dodge Dan Barendregt (130Pts.)

0

Can the parking light wire be hooked up to another source?

I have a 2010 Ram 2500 with gas engine. I have a set of Rock lights underneath my truck for an awesome look when it is parked. Can I hook up the Signal wire from the 20 pin harness of a EVO-CHRT4 to these lights instead of to the parking lights? these Rock lights draw 4.5 amps. Could I connect the signal wire to the ground of these rock lights?
Connectez-vous pour répondre Voir 1 réponse(s)

No results

picto contact

Vous cherchez nos meilleurs participants ?

Voir les utilisateurs
picto contact

Vous n'avez pas trouvé ce que vous cherchiez ?

Posez une question

Support Technique

Recherchez parmi nos produits les plus populaires et les sujets d'installation disponibles dans notre section Questions et réponses.

En savoir plus
Téléchargez notre application de guides de dépannage étape par étape disponible pour iOS et Android ou parcourez notre version de bureau.

En savoir plus
Accédez à la plus grande base de données de schémas de câblage et de photos en ligne de l'industrie. Un jeton gratuit est fourni dans chaque boîte EVO-SERIES.

En savoir plus
Vous n'avez pas trouvé l'information que vous cherchiez ? Posez-nous une question en remplissant le formulaire de demande de support technique. Un spécialiste produit vous répondra sous peu.

En savoir plus
Des solutions de contrôle à distance et de connectivité à la fine pointe de la technologie au soutien technique haut de gamme, découvrez pourquoi vous devriez choisir les produits Fortin.

En savoir plus

Ce site Web utilise des cookies pour vous garantir la meilleure expérience utilisateur. En poursuivant votre navigation sur notre site, vous acceptez notre utilisation des cookies. En savoir plus Continuer